The GATE Grind

GATE Electrical and Electronic Measurements: Measurement of voltage, current, power, energy and power factor – Previous Year Questions

18 GATE previous year questions on Measurement of voltage, current, power, energy and power factor (Electrical and Electronic Measurements, Electrical Engineering) with answers and explanations, from every paper.

18 questions worth 28 marks in all (8 1-mark, 10 2-mark). Asked between 2014 and 2025, so you can see how the topic has been tested over time.

  1. GATE 2015 EE (EE2) Q15 (1 mark, Multiple choice) – Match P: permanent-magnet moving coil; Q: moving iron through a current transformer; R: rectifier instrument; S: electrodynamometer, to 1: DC only; 2:…
  2. GATE 2015 EE (EE2) Q16 (1 mark, Multiple choice) – A balanced three-phase load consumes 5 kW at pf 0.707, measured by the two-wattmeter method. The readings are
  3. GATE 2016 EE (EE2) Q64 (2 marks, Numerical answer) – An energy meter with constant 1200 revolutions/kWh makes 20 revolutions in 30 seconds at constant load. The load in kW is .
  4. GATE 2014 EE (EE2) Q29 (1 mark, Numerical answer) – The sawtooth shown drives a moving-iron voltmeter. Find its approximate reading (V).
  5. GATE 2014 EE (EE2) Q30 (1 mark, Numerical answer) – Two wattmeters read 100 W and 250 W for a balanced three-phase load. Find load power factor.
  6. GATE 2014 EE (EE2) Q58 (2 marks, Numerical answer) – Ammeters X,Y have resistances 1.2 Ω,1.5 Ω and full-scale currents 150 mA,250 mA respectively. Shunts extend each to 15 A full scale. The shunted…
  7. GATE 2014 EE (EE1) Q29 (1 mark, Multiple choice) – Two wattmeters measure power of a balanced three-phase, three-wire load. The first reads twice the second. Find load-impedance angle (rad).
  8. GATE 2014 EE (EE1) Q57 (2 marks, Numerical answer) – Find the rms voltmeter reading (V) for the circuit shown.
  9. GATE 2014 EE (EE1) Q58 (2 marks, Numerical answer) – DC current is measured by series-connected PMMC and electrodynamometer ammeters. The PMMC has 100 turns, air-gap flux density 0.2 Wb/m² and coil area…
  10. GATE 2017 EE Q33 (1 mark, Numerical answer) – The following measurements are obtained on a single phase load: V = 220 V 1 %, I = 5.0 A 1% and W = 555 W 2 %. If the power factor is calculated using…
  11. GATE 2017 EE Q44 (2 marks, Multiple choice) – The load shown in the figure is supplied by a 400 V (line-to-line), 3-phase source (RYB sequence). The load is balanced and inductive, drawing 3464…
  12. GATE 2015 EE Q16 (1 mark, Numerical answer) – A (0-50 A) moving coil ammeter has a voltage drop of 0.1 V across its terminals at full scale deflection. The external shunt resistance (in milliohms)…
  13. GATE 2016 EE Q63 (2 marks, Numerical answer) – A dc voltage with ripple is given by v(t) = [100 + 10( t) - 5(3 t)] volts. Measurements of this voltage v(t), made by moving-coil and moving-iron…
  14. GATE 2018 EE Q15 (1 mark, Multiple choice) – Two wattmeter method is used for measurement of power in a balanced three-phase load supplied from a balanced three-phase system. If one of the…
  15. GATE 2019 EE Q42 (2 marks, Multiple choice) – A moving coil instrument having a resistance of 10\ , gives a full-scale deflection when the current is 10 mA. What should be the value of the series…
  16. GATE 2023 EE Q39 (2 marks, Multiple choice) – A 3-phase, star-connected, balanced load is supplied from a 3-phase, 400 V (rms), balanced voltage source with phase sequence R-Y-B, as shown in the…
  17. GATE 2024 EE Q50 (2 marks, Numerical answer) – In the circuit shown, Z 1=50-90\ and Z 2=200-30\ . It is supplied by a three phase 400 V source with the phase sequence being R-Y-B. Assume the watt…
  18. GATE 2025 EE Q58 (2 marks, Numerical answer) – In an experiment to measure the active power drawn by a single-phase RL Load connected to an AC source through a 2 Ω resistor, three voltmeters are…