The GATE Grind

GATE 2019 PI – Previous Year Questions with Solutions

All 65 questions of GATE 2019 PI with answers and explanations. Read each question, then practise it by topic or as a full paper.

65 questions worth 100 marks in all (30 1-mark, 35 2-mark). Subjects covered: General Engineering (11), General Aptitude (10), Quality and Reliability (10), Engineering Mathematics (9), Operations Research and Operations Management (9), Manufacturing Processes I (7), Manufacturing Processes II (6), Industrial Engineering (3).

Practise this paper in The GATE Grind →

  1. Question 1 (1 mark, Multiple choice) – The fishermen, the flood victims owed their lives, were rewarded by the government.
  2. Question 2 (1 mark, Multiple choice) – Some students were not involved in the strike. If the above statement is true, which of the following conclusions is/are logically necessary? I. Some…
  3. Question 3 (1 mark, Multiple choice) – The radius as well as the height of a circular cone increases by 10%. The percentage increase in its volume is
  4. Question 4 (1 mark, Multiple choice) – Five numbers 10, 7, 5, 4 and 2 are to be arranged in a sequence from left to right following the directions given below: 1. No two odd or even numbers…
  5. Question 5 (1 mark, Multiple choice) – Until Iran came along, India had never been in kabaddi.
  6. Question 6 (2 marks, Multiple choice) – Since the last one year, after a 125 basis point reduction in repo rate by the Reserve Bank of India, banking institutions have been making a demand…
  7. Question 7 (2 marks, Multiple choice) – In a country of 1400 million population, 70% own mobile phones. Among the mobile phone owners, only 294 million access the Internet. Among these…
  8. Question 8 (2 marks, Multiple choice) – The nomenclature of Hindustani music has changed over the centuries. Since the medieval period dhrupad styles were identified as baanis. Terms like…
  9. Question 9 (2 marks, Multiple choice) – Two trains started at 7 AM from the same point. The first train travelled north at a speed of 80 km/h and the second train travelled south at a speed…
  10. Question 10 (2 marks, Multiple choice) – "I read somewhere that in ancient times the prestige of a kingdom depended upon the number of taxes that it was able to levy on its people. It was…
  11. Question 11 (1 mark, Multiple choice) – For any real, square and non-singular matrix B, the B-1 is
  12. Question 12 (1 mark, Multiple choice) – For a complex number z=1-4i with i=-1, the value of z+3z-1 is
  13. Question 13 (1 mark, Multiple choice) – The vector that is normal to the surface 2xz2-3xy-4x=7 at the point (1,-1,2) is
  14. Question 14 (1 mark, Multiple choice) – If roots of the auxiliary equation of d2ydx2+adydx+by=0 are real and equal, the general solution of the differential equation is
  15. Question 15 (1 mark, Multiple choice) – The solution of 1a 1bdx\,dyxy is
  16. Question 16 (1 mark, Multiple choice) – Match the crystal structure in Column A with the corresponding packing fractions in Column B. Column A: 1. Simple cubic; 2. Hexagonal close-packed; 3.…
  17. Question 17 (1 mark, Multiple choice) – The link lengths of a planar four-bar mechanism are AB=100 mm, BC=25 mm, CD=75 mm and DA=90 mm. For achieving the full rotation of both the input…
  18. Question 18 (1 mark, Multiple choice) – The process used for producing continuous insulation coating on an electrical wire is
  19. Question 19 (1 mark, Multiple choice) – The correct statement pertaining to the friction welding process is
  20. Question 20 (1 mark, Multiple choice) – The end product obtained using spinning process is shown in the figure. The initial blank thickness is 2.5 mm. The blank diameter (in mm) is
  21. Question 21 (1 mark, Multiple choice) – For a classical (Wilson) model of determining economic order quantity (EOQ), the carrying and ordering costs are C r and C o, respectively. For an…
  22. Question 22 (1 mark, Multiple choice) – A company has purchased an asset by investing Rs. 30,000. The useful life of the asset is 5 years and it has no salvage value at the end of its useful…
  23. Question 23 (1 mark, Multiple choice) – In an NC milling operation, the tool path is generated using absolute programming for the trajectory shown in the figure. The corresponding block of…
  24. Question 24 (1 mark, Multiple choice) – The SQC chart based on Binomial distribution is
  25. Question 25 (1 mark, Multiple choice) – The capacity of a passenger airline is expressed in terms of
  26. Question 26 (1 mark, Multiple choice) – REL chart is used in
  27. Question 27 (1 mark, Numerical answer) – A metallic rod of diameter d 0 is subjected to the tensile test. The engineering stress and the true stress at fracture are 800 MPa and 900 MPa,…
  28. Question 28 (1 mark, Numerical answer) – A heat pump is to supply heat at the rate of 10 kW to a building to be maintained at 22 C. The outside temperature is 2 C. The minimum power (in kW)…
  29. Question 29 (1 mark, Numerical answer) – One kilogram of air is compressed at constant temperature of 150 C until its volume is halved. Considering gas constant R=0.287 kJ/kg-K for air,…
  30. Question 30 (1 mark, Numerical answer) – For the abrasive jet machining process, the ratio of abrasive volume to carrier gas volume is 0.25. Further, the ratio of abrasive density to carrier…
  31. Question 31 (1 mark, Numerical answer) – In a typical turning tool life test, the following data are generated for tools A and B: Tool A: cutting speed 200 m/min, tool life 20 min; Tool B:…
  32. Question 32 (1 mark, Numerical answer) – The average proportion non-conforming of 20 samples each of size 100 items is 0.12. The upper control limit for the relevant chart is (round off to 2…
  33. Question 33 (1 mark, Numerical answer) – For a process which is in a state of statistical control (within 3), estimated process standard deviation () is 3 mm. The specification limits for the…
  34. Question 34 (1 mark, Numerical answer) – In a work study experiment, normal time was recorded as 140 s with a rating of 100%. Considering 2% allowance, the standard time (in s) is (round off…
  35. Question 35 (1 mark, Numerical answer) – A warehouse has 1 loading dock and 3 persons for loading operations. The arrival rate of trucks follows Poisson distribution with a mean of 4…
  36. Question 36 (2 marks, Multiple choice) – If the Laplace transform of e t is 1s-, the Laplace transform of t t is
  37. Question 37 (2 marks, Multiple choice) – The general solution of the Cauchy-Euler equation x2d2ydx2-7xdydx+16y=0 is
  38. Question 38 (2 marks, Multiple choice) – A uniform cantilever beam ABC of length L is subjected to a point load P at point B and a concentrated moment M at point C (as shown). Let E be the…
  39. Question 39 (2 marks, Multiple choice) – Three Carnot engines E 1, E 2, E 3 operate as shown in the figure (T 1>T 2>T 3). The efficiency of engine E 3 in terms of the efficiencies 1 and 2 of…
  40. Question 40 (2 marks, Multiple choice) – True centrifugal casting process in horizontal configuration is to be used for casting a metallic cylinder with outside diameter 0.275 m and inside…
  41. Question 41 (2 marks, Multiple choice) – In a sine bar, let h denote height of slip gauge and l be the distance between the rollers. The relationship between error in angular measurement (d)…
  42. Question 42 (2 marks, Multiple choice) – A 100 mm long cylindrical workpiece of diameter 50 mm is reduced to 25 mm diameter using extrusion process. The flow curve for the metal has strength…
  43. Question 43 (2 marks, Multiple choice) – A linear programming problem (LPP) is defined as: Minimize z=15x 1+12x 2, subject to x 1+2x 2 3, 2x 1-4x 2 5, and x 1,x 20. The objective function of…
  44. Question 44 (2 marks, Multiple choice) – A 20 mm HSS drill with a point angle of 118 degrees is used for drilling a through hole on a metallic plate of thickness 100 mm with a cutting speed…
  45. Question 45 (2 marks, Multiple choice) – An acceptance sampling plan is selected with sample size n=80, acceptance number c=2 for a lot size of 10,000 units. The probability of accepting the…
  46. Question 46 (2 marks, Multiple choice) – The mean time to repair (MTTR) for a repairable system is 30 minutes. When maintenance time changes from 20 minutes to 40 minutes, the net increase in…
  47. Question 47 (2 marks, Multiple choice) – A company invests Rs. 50 thousand in assets. The initial investment is Rs. 30 thousand with two subsequent investments of Rs. 10 thousand each at the…
  48. Question 48 (2 marks, Multiple choice) – The man-hours required (T n) to manufacture the nth unit in a plant is given by T n=T 1nb, where b=-0.322 at the 80% learning rate. If the…
  49. Question 49 (2 marks, Multiple choice) – A firm with a production target of 50,000 units/year has the following data for selection of a new plant location: location P has fixed cost Rs.…
  50. Question 50 (2 marks, Multiple choice) – Considering included angle of the thread to be 60 degrees using the Best-Wire method, the difference between the effective diameter (E) and the…
  51. Question 51 (2 marks, Numerical answer) – If z is a complex variable with i=-1, the length of the minor axis of an ellipse defined by z-(1+i) + z-(9+i) =10 is
  52. Question 52 (2 marks, Numerical answer) – The numerical value of the definite integral 01 e-x\,dx using the trapezoidal rule with function evaluations at points x=0, 0.5 and 1 is (round off to…
  53. Question 53 (2 marks, Numerical answer) – A thin-walled cylindrical pressure vessel with an inside diameter of 300 mm and wall thickness of 3 mm is subjected to an internal gauge pressure of…
  54. Question 54 (2 marks, Numerical answer) – A cam is designed to achieve a simple harmonic motion of a flat-faced follower. Starting from the rest, the follower rises to the maximum height of 50…
  55. Question 55 (2 marks, Numerical answer) – An open tank of 2\,m2\,m2\,m is filled with layers of two fluids. The depth of each layer is one meter. The top layer is oil of specific gravity 0.8,…
  56. Question 56 (2 marks, Numerical answer) – During a storm, the wind speed is 90 km/hr. In a high-rise building, there is a window of size 1.2 m 1.8 m facing the storm on an upper floor.…
  57. Question 57 (2 marks, Numerical answer) – The heat transfer efficiency in arc welding of a plate using a current of 250 A at 20 V is 90%. The heat required to melt the material is 10 J/mm3. If…
  58. Question 58 (2 marks, Numerical answer) – A sand casting process has a mold constant of 2 s/mm2 and solidification exponent of 2. If the solidification time is to be doubled for a given unit…
  59. Question 59 (2 marks, Numerical answer) – During a turning operation of a specific work material having shear strength of 220 MPa under orthogonal cutting condition, the process parameters…
  60. Question 60 (2 marks, Numerical answer) – A CO 2 laser in continuous mode is used for drilling a plate. The process parameters are: laser power intensity 1108 W/mm2, vaporization energy 5106…
  61. Question 61 (2 marks, Numerical answer) – A process which is in a state of statistical control (within 3) has an estimated standard deviation () of 2 mm. The specification limits for the…
  62. Question 62 (2 marks, Numerical answer) – A monitoring system has seven components. The reliability of each component is shown in the figure. The system reliability is (round off to 2 decimal…
  63. Question 63 (2 marks, Numerical answer) – A PERT project network consists of 5 activities A to E. Activity predecessor-successor (P-S) relationships and time estimates (optimistic, most…
  64. Question 64 (2 marks, Numerical answer) – The sales data of a product for 5 years are: 2014: 280 units; 2015: 268 units; 2016: 259 units; 2017: 270 units; 2018: 287 units. Assume the forecast…
  65. Question 65 (2 marks, Numerical answer) – The layout for an AGV system is shown in the figure. The loading time is 0.5 minutes and the unloading time is also 0.5 minutes. All distances are in…