The GATE Grind

GATE Steel Structures: Connections: simple, eccentric, beam-column – Previous Year Questions

17 GATE previous year questions on Connections: simple, eccentric, beam-column (Steel Structures, Civil Engineering) with answers and explanations, from every paper.

17 questions worth 30 marks in all (4 1-mark, 13 2-mark). Asked between 2016 and 2026, so you can see how the topic has been tested over time.

  1. GATE 2017 CE (CE1) Q53 (2 marks, Numerical answer) – A column carries a 10 kN load through the bracket shown, at eccentricity 15 cm from the bolt-group centre. The four-bolt geometry, 10 cm dimensions…
  2. GATE 2016 CE (CE2) Q47 (2 marks, Multiple choice) – Two bolted plates under tension have the alternative hole arrangements in Figures 1 and 2. Hole diameter, pitch and gauge are d,p,g, respectively.…
  3. GATE 2016 CE (CE1) Q48 (2 marks, Multiple choice) – Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the figure. The thickness of each plate is 12 mm. The…
  4. GATE 2017 CE (CE2) Q51 (2 marks, Numerical answer) – Two 8 mm steel plates are connected by 6 mm fillet welds as shown. Allowable plate and weld stresses are 150 and 110 MPa. Treat the indicated weld…
  5. GATE 2018 CE (CE2) Q33 (1 mark, Numerical answer) – A fillet weld simultaneously carries factored normal stress 120 MPa and shear stress 50 MPa. According to IS 800:2007 referred to in the paper,…
  6. GATE 2018 CE (CE2) Q40 (2 marks, Multiple choice) – Four equal-diameter bolts P, Q, R and S hold a bracket carrying 130 kN as shown. The force in bolt P is .
  7. GATE 2018 CE (CE1) Q29 (1 mark, Numerical answer) – A fillet weld has direct shear stress 50 MPa and bending tensile stress 150 MPa. According to IS 800:2007 referred to in the paper, equivalent stress,…
  8. GATE 2019 CE (CE1) Q46 (2 marks, Numerical answer) – A 16 mm gusset plate is connected to a 12 mm I-section flange by 10 mm fillet welds on both sides as shown. Each weld is 500 mm long. A 350 kN point…
  9. GATE 2020 CE (CE2) Q54 (2 marks, Numerical answer) – Two steel plates are lap-jointed in a workshop with 6 mm fillet weld as shown. Weld ultimate strength is 410 MPa. As per IS 800:2007 limit-state…
  10. GATE 2020 CE (CE1) Q52 (2 marks, Numerical answer) – The doubly symmetric built-up section shown has flange/web plates joined by continuous 10 mm fillet welds. About X–X, I=7.73106 mm⁴. Permissible weld…
  11. GATE 2021 CE (CE1) Q50 (2 marks, Numerical answer) – A six-bolt bracket carries 60 kN downward at eccentricity 100 mm. Bolts are in two columns x=±40 mm and three rows y=−30,0,30 mm. R is the middle bolt…
  12. GATE 2022 CE (CE1) Q38 (2 marks, Multiple choice) – A weld is used for joining an angle section ISA 100 mm × 100 mm × 10 mm to a gusset plate of thickness 15 mm to transmit a tensile load. The…
  13. GATE 2023 CE (CE2) Q40 (2 marks, Multiple choice) – Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the figure. The thickness of each plate is 12 mm. The…
  14. GATE 2023 CE (CE1) Q31 (1 mark, Numerical answer) – Consider the fillet-welded lap joint shown in the figure (not to scale). The length of the weld shown is the effective length. The welded surfaces…
  15. GATE 2025 CE (CE2) Q37 (2 marks, Multiple choice) – A circular tube of thickness 10 mm and diameter 250 mm is welded to a flat plate using 5 mm fillet weld along the circumference. Assume Fe410 steel…
  16. GATE 2025 CE (CE1) Q54 (2 marks, Numerical answer) – Consider the built-up column made of two I-sections as shown in the figure, with each batten plate bolted to a component I-section of the column…
  17. GATE 2026 CE (CE1) Q30 (1 mark, Numerical answer) – Two steel plates are to be connected together by a 5 mm fillet weld of length 150 mm to transfer a design load. If the size of the fillet weld used to…